E510 PCI DRIVER

See the label on the module to determine the module’s capacity. If you insert the module correctly, the securing clips snap into the cutouts at each end of the module. If you are installing a processor upgrade kit from Dell, discard the original heat-sink assembly. Always install DDR2 memory modules in the order indicated on the system board. Media Card Reader Optional. Ground yourself by touching an unpainted metal surface on the back of the computer. You must route the DC power cables properly through the routing clips when you replace the cables to prevent them from being pinched or crimped.

Uploader: Tygokinos
Date Added: 14 July 2013
File Size: 25.97 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 98191
Price: Free* [*Free Regsitration Required]

Any address space reserved for these components cannot be used by computer memory.

FlexBay for optional floppy drive or optional Media Ppci Reader. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment. To connect a network cable, first plug the cable into the network port or device, and then plug the cable into the computer.

Removing and Installing Parts: Dell Dimension /E Service Manual

If you installed a processor replacement kit from Dell, return the original heat-sink assembly and processor to Dell in the same package in which your replacement kit was sent. The mounting-bracket screws need to be removed for the removal of the system board. If necessary, disconnect any cables connected to the card. Certain components within d510 computer require address space in the 4-GB range. Do not install ECC or buffered ;ci modules.

When you install the heat-sink assembly, do not touch the thermal interface on its underside, as this may result in damage to the thermal interface material. If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure. Ensure that the assembly has had pcj time to cool before you touch it. Ensure that you release the securing tab to unseat the card. To e150 static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer’s electronic components.

  FUSIONIO LINUX DRIVER

If the card is not removed correctly, the system board may be damaged. Leave the release lever extended in the release position so that the socket is ready for the new processor. To avoid damage to the drive, do not set it on a e5110 surface. To avoid damage, ensure that the processor aligns properly with the socket, and do not use excessive force when you install the processor.

You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when you turn on the computer. Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.

When removing or replacing the processor, 5e10 not touch any of the pins inside the processor socket or allow any objects to fall onto the pins in the socket. If you are installing a PCI Express x16 card, the card may cover the floppy-drive connectors. If you are installing or replacing a PCI Express card, follow the procedures e150 the next section. When you connect two IDE devices to a single IDE interface cable and configure them for the cable select setting, the device attached to the last connector on the interface cable is the master or boot device ee510 0and the device attached to the middle connector on the interface cable is the slave device drive 1.

  INTEL Q35 EXPRESS AUDIO DRIVER

Your computer supports DDR2 memory. Use care when handling the front-panel release tabs to avoid damaging them. Always install DDR2 memory modules in the e5510 indicated on the system board.

Despite having a plastic shield, the heat-sink assembly may be very hot during normal operation.

Dell Dimension

To guard against electrical shock, be sure to unplug your computer from its electrical outlet before installing any cards. When you install a filler bracket, ensure that the bracket is seated correctly.

Some network adapters automatically start the computer when they are connected to a network. To avoid damage to the memory module, press the module straight down into the connector while you apply equal force to each end of the module.

To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network port or device. See the drive documentation in your upgrade kit for information on configuring devices for the cable select setting.

While you work, periodically touch an unpainted metal surface to dissipate any static electricity pfi could harm internal components.